http://www.apple.com/macosx/

1. Optional but Highly recommend: install Tiger first. This can be done by inserting Tiger DVD on your computer and make sure you boot from it. Usually that’s done if you press F8 or F12 or whatever key combination to give you the option to choose what disk/cd drive you want to boot from. Or you can always change boot device in BIOS setup. Select your CD/DVD drive. And



Select your language and when the welcome screen shows up



   1. Select Utilities -> Disk Utility

   2. Select your partition that you want to be OSX and go to the Erase tab

   3. For Volume Format, select Mac OS Extended (Journaled), set volume name as “Leopard“(no quotes, case sensitive)

   4. Click Erase. Now the partition should not be grey, it should be black to indicate that it is active.

   5. Close out of the Disk Utility and move onwards with installation.



Use “Customize” option and unselect all packages there. Just install base system. By installing Tiger first, the partition would be properly formatted and activated, which eliminate any potential problem. Now reboot and remove the Tiger DVD.



2. Install Leopard.



Insert Leopard DVD, and make sure to select booting from DVD. The installer will load(it will take a while, be patient). If you have Tiger installed, don’t format the partition, just install it over the Tiger partition. Otherwise, same approach as Tiger installation, use Disk Utility to setup the partition.



Important: Use Customize… button and unselect all packages there. Then proceed to installation. When it’s done, reboot. And make sure that your USB/Pen Drive is connected to your PC.



Patch Leopard Installation



After the reboot, also make sure you do the same step above: Press whatever key combination to give you the option to choose your boot device: Now Select your CD/DVD drive.



Once the setup is loaded(again, long wait, be patient), select your language. When the welcome screens shows up, select UTILITIES-TERMINAL. The terminal will now open. We will now browse to our Thumb Drive;



In the command line, type:



cd /Volumes/123/files



Lets now run the script. This will patch the installation so it will boot properly:



./9a581PostPatch.sh



Let it run. You can answer yes when removing the ACPUPowerManagement.kext



Reboot.

  1. Reboot using the Leopard DVD, make sure the USB pen drive is connected.

   2. Open a terminal after everything finally loads.

   3. Find out what disk your leopard was installed on by issuing this command (my machine was rdisk0s2, will use rdiskXsY below, substitute accordingly)



      diskutil list



   4. Active the partition



      fdisk -e /dev/rdiskX

      fdisk: 0>update

      fdisk:*0> f Y

      “Partition 2 marked active”

      fdisk:*0> w

      Device could not be accessed exclusively.

      A reboot will be needed for changes to take effect. OK? [n]y

      Writing MBR at offset 0.

      fdisk: 0> q



   5.



      Now goto bootfix directory by typing:



      cd /Volumes/123/files/bootfix



      and do the following



      ./dd if=/usr/standalone/i386/boot1h of=/dev/rdiskXsY bs=512 count=1

      umount /Volumes/Leopard

      ./startupfiletool -v /dev/rdiskXsY /usr/standalone/i386/boot

      ./bless -device /dev/diskXsY -setBoot -verbose

2. Now you’re already in the exciting Leopard! After initial setup, load up Terminal(Applications/Utilities) within OSX and type



sudo nano /Library/Preferences/SystemConfiguration/com.apple.Boot.plist



edit the Darwin time-out flag accordingly:



<key>Timeout</key>

<string>10</string>



reboot and now you can choose Mac OSX/XP/Vista using Leopard’s boot loader.



3. Optional: you can also setup Windows as default OS and use windows’ OS selector to launch OSX.

1. Type diskpart

   2. If you have more than one disk, at the DISKPART prompt, type:

      list disk

   3. At the DISKPART prompt, type:

      select disk x

      Select the disk, x, where the partition you want to mark as active in

   4. At the DISKPART prompt, type:

      list partition

   5. At the DISKPART prompt, type:

      select partition y

      Select the partition, y, you want to mark as active.

   6. At the DISKPART prompt, type:

      active

      to active the selected partition and system will boot from it next time.

   7. At the DISKPART prompt, type:

      exit

      to quit the diskpart program

[boot loader]

timeout=0

default=c:\tboot      



[operating systems]      



c:\tboot="Mac OSX Leopard"

  1.put tboot on Vista boot partition, usually C:\

   

  2. Open a command prompt and make sure it’s running as administrator and type:



      bcdedit /create /d "Mac OSX Leopard" /application bootsector



      This will retrun a {ID}

   3. Use the command line below to add the tboot, replace the {ID} accordingly:



      bcdedit /set {ID} device boot      



      bcdedit /set {ID} path \tboot      



      bcdedit /displayorder {ID} /addlast

Links are interchangeable between RS & MU 



Rapidshare


		
		
		
		

			
contains hidden content
			

		
Megaupload

		
		
		
		

			
contains hidden content